Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket immobiliser for CAN bus. It is discreet and does not have LED indicators or key fobs and is hidden within the vehicle's wiring.
It also allows the user to temporarily disable the system by using Transport Mode in the event of renting out their vehicle. This guide will walk you through the steps of installing a Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser is a modern security device that guards your vehicle against hacking, key cloning, and relay attacks. The system is connected directly to the ECU of your vehicle and protected by a PIN code you set. It is inaccessible to thieves using diagnostic scanners or other modern methods, and is unable to be disabled by cutting circuits.
The system is easy to use, but professional installation is recommended to ensure a clean connection to the ECU of your vehicle. Installers approved by Thatcham can assist with the installation and programing of your Ghost system. They can also recommend an alarm or tracking system to complete the security package for your vehicle.
To avoid an accidental deployment of airbags or short circuits The installer must first disconnect your battery. After this is completed the installer is able to safely begin work. Hand tools are the most basic to be used to ensure precise connections. A multimeter is useful to check electrical values. Insulation tape and cable tie are crucial to ensure connections are secure and keep wiring tidy. In addition, the user's manual gives specific guidelines that are tailored to your Ghost Immobiliser model.
During the installation process, it's crucial to select an area for grounding that is free of paint and debris. Installers should also make sure that the immobiliser's wires CAN H and CAN L are connected to the appropriate ECU ports. The wires can be connected or soldered depending on the model. A high-quality connector is recommended to ensure a sturdy and reliable connection.
Once the installation is complete, the customer can activate the Transport Mode. This allows mechanics or valet parking to use the vehicle, without knowing the pin code. To do this, the customer must press the button for service on the dashboard 5 times in a matter of 2 seconds. The system will confirm this by displaying 5 indicators.
The Autowatch Ghost 2 immobiliser is TASSA approved and is a highly efficient immobiliser. It's a smart option for those who regularly rents their vehicle on platforms such as Turo. An immobiliser can cut down on the cost of insurance, as it decreases the likelihood of theft.
Getting Started
If you are looking for a solution to safeguard your vehicle from theft it is best to go with an autowatch ghost immobiliser. The device protects your vehicle from starting even when a criminal steals or copies the key. It's possible because of its advanced technology that stops the engine from starting until the correct PIN code is entered.
The device connects to the CAN bus network of your vehicle which allows it to communicate with the ECU directly. It makes use of the buttons on your dashboard and steering wheel to create a unique sequence, which only you know. This makes it impossible for anyone else to start your car. This is the most secure way to safeguard your pride and joy. It will keep its value intact if you ever want to sell it.
Installing a ghost immobiliser is a simple process, but it is crucial to follow the steps carefully to avoid electrical issues and system malfunctions. You'll need to find a 12V power source and a good grounding on the car's chassis. After that, you can begin connecting the wires to the immobiliser. Make sure to use high-quality connectors and soldering methods to ensure a strong connection. Also, be sure to insulate the connections by using heat shrink tubing or insulation tape to protect them from short circuits in electrical power and other issues.
After the wires are connected, you are able to connect the battery and start the engine to test whether the immobiliser is functioning. When cost of ghost immobiliser is functioning correctly you can place it in a safe location under the dash or elsewhere in the vehicle. Make sure you hide it properly to stop a thief from tampering with it.
The Ghost 2 immobiliser has been TASSA (Tracker and Aftermarket Security System Association) which means it is a high-quality deterrent for car thieves. It provides superior protection against key cloning, hacking, and relay attacks. It cannot be disabled without knowing the code. The device is easy to use, and can be set to an option for a service valet so that your vehicle won't be activated when you take it to an MOT or for servicing.
Wiring
The Ghost Immobiliser is a cutting-edge security system designed to stop theft of vehicles. It communicates with your vehicle's ECU and connects directly to its CAN bus. Contrary to other aftermarket systems which require the removal of circuit components The Ghost Immobiliser does not interfere with any of the factory settings for your vehicle.
It's also totally undetectable by thieves using diagnostic scanning devices. This is due to the fact that it doesn't send and receive radio frequency signals, and it uses the CAN data to communicate with your ECU. In addition, it doesn't need any modifications to your vehicle's existing key fobs.
To use the Ghost Immobiliser, simply switch on the ignition of your car and then enter the sequence to disarm (either one or two buttons). The indicator will flash twice to verify that you have entered the correct code. Once you've verified this, you're able to start your vehicle and leave in peace.
Once installed The Ghost Immobiliser can protect your car from key cloning and hacking and will also protect the value of your pride and joy. If you ever need to surrender your car to valet parking or for service, the Ghost Immobiliser can be temporarily disabled in Transport Mode.
You'll require a constant power source (12V) as well as an earthing point to complete the installation of a Ghost immobiliser. Ensure that these are both well-insulated and safe to touch. Cable ties are also recommended to secure the wires. This will reduce the chance of theft by thieves. To avoid committing mistakes, double-check these points and mark them using a label or tape. Examine all connections for signs they're wearing out. Connections that are loose can cause problems with the system, so be sure they're securely in place and securely insulated. Make sure to test your Ghost Immobiliser after installation has been completed. This will ensure that the unit is operating correctly, and that all connections are secure and insulated. Be sure to fix any issues immediately.
Testing
The Autowatch Ghost immobiliser is a revolutionary vehicle security system that works seamlessly with your vehicle's ECU to prevent unauthorized motor starting. Its cutting-edge technology safeguards your vehicle from key cloning and hacking and other methods that thieves employ to steal cars. The Ghost is also able to work in conjunction with other alarm and tracking systems to give the most complete protection for your vehicle. The Ghost's unparalleled features, coupled with its subtle design, make it a popular option for both car enthusiasts as well as security-conscious drivers.
It is essential to follow the steps of installation to ensure complete integration of the Ghost Immobiliser. Refer to the wiring diagram of the vehicle as it will help you locate and connect the wires. The next step is to identify the power source as well as grounding points. Once you've found them you'll be required to mark them so that they're easy to identify during the installation process. It is essential to use top-quality materials and tools. Basic hand tools will aid in making precise connections. A multimeter will check electrical values, and ensure security. Insulation tape and cable ties will help keep all connections tidy and neat. Also, a user's guide will give specific guidelines specific to your Ghost model.
Before you begin installing it is essential to test the system by entering the PIN code, then starting the vehicle. This will ensure that the immobiliser functions according to plan, and prevents unauthorised vehicle start-ups. This procedure should be carried out frequently as part of your regular vehicle inspections in order to ensure the system is always functioning properly.
Once the installation is complete, you can drive your car with confidence. The Ghost will keep your precious possessions safe from would-be thieves and ensure that no one can take off with your vehicle without the correct PIN. The Ghost can also be paired with a Thatcham-approved tracker to detect any attempts at tampering or theft, allowing you to locate your vehicle if it's stolen.
The Ghost can be used on a variety of vehicles and is compatible with the majority of major brands. If you're interested in protecting your car with this innovative device, contact Monty's Locksmith today to find out more about our installation and maintenance options. We are a TASSA Registered installer This certification ensures that we adhere to strict guidelines and procedures for installing our products. This assures customers, insurance companies, and law enforcement that all installations are completed safely and correctly.